| Display |
Module Health, In Calibration,Mode
|
|---|---|
| Input Signal |
0-20mA, 4-20mA
|
| Isolation |
250V (continuous), reinforced,insulation type, inputs to,backplane
|
| Number Of Channels |
8
|
| Special Features |
Supports HART Protocol
|
| Input, current |
Yes
|
|---|---|
| Input, voltage |
Yes
|
| Input, resistor |
No
|
| Input, resistance thermometer |
No
|
| Input, thermocouple |
No
|
| Input signal, configurable |
Yes
|
| Output, current |
No
|
| Output, voltage |
No
|
| Output signal configurable |
No
|
| Analogue inputs configurable |
Yes
|
| Analogue outputs configurable |
No
|
| Type of electric connection |
Screw-/spring clA connection
|
| Input offset drift with temperature |
<=300 µA/°C
|
| Wire type |
Copper
|
| Terminal block torque specifications |
1756-TBCH: 0.5 Nm (4.4 in-lb)
|
| Inrush current |
400mA @ 5V, 450mA @ 24V
|
| Input conversion method |
Sigma-Delta ADC (24-bit converter)
|
| Module keying |
Electronic, software configurable
|
| Module error over full temperature range |
0.3% of range (all filters) with HART disabled
|
| Input range |
0...20 mA (0...20.58 mA), 4...20 mA (3.42...20.58 mA)
|
| Data format |
32-bit floating point
|
| Wire category |
2 - on signal ports
|
| Common mode noise rejection |
>90 dB @ 50/60 Hz (10 Hz, 15 Hz or 20 Hz filters only)
|
| Normal mode noise rejection |
>90 dB @ 50 Hz and 60 Hz with 10 Hz filter, >74 dB @ 50 Hz and 60 Hz with 15 Hz filter, >33 dB @ 50 Hz and >90 dB @ 60 Hz with 20 Hz filter
|
| Gain drift with temperature |
20 ppm/°C
|
| Voltage and current ratings |
Backplane: 210mA @ 5.1V DC, 110mA @ 24V DC, Input voltage range: 5...30V DC, Input current range: 0...20mA @ 4...20mA
|
| Typical module HART dynamic variables update time for all channels |
1 s typical if all channels are HART enabled Pass through messages, handheld communications, sary masters, communication errors, or configuration changes can significantly increase the update time.
|
| Module scan time |
18...488 ms (filter dependent) for all channels - analog, minimum
|
| Inputs |
Eight current inputs
|
| Resolution |
16 to 21 bit
|
| Wire size |
Single wire connection (1756-TBCH): 0.33...2.1 mm² (22...14 AWG) solid or stranded shielded copper wire, rated at 105 °C (221 °F) or greater, 1.2 mm (3/64 in.) insulation maximum, Single wire connection (1756-TBS6H): 0.33...2.1 mm² (22...14 AWG) solid or
|
| Calibrated accuracy |
0.15...1.5% of full scale, filter dependent@ 25 °C with HART disabled, 1.5% of full scale with 250 Hz filter @ 25 °C with HART enabled, 0.5% of full scale with 100 Hz filter @ 25 °C with HART enabled, 0.2% of full scale with 50 Hz or 60 Hz filter @ 25 °C
|
| Open circuit detection time |
5 s (4...20 mA range only)
|
| Suitable for safety functions |
No
|
| Power dissipation within module |
4 W
|
| Input overvoltage protection |
28.8V DC
|
| Surrounding air temperature, max |
60 °C
|
|---|---|
| North American temperature code |
T5
|
| Emissions |
IEC 61000-6-4
|
| ESD immunity |
6 kV contact discharges, 8 kV air discharges
|
| EFT/B immunity |
±2kV @ 5kHz on signal ports
|
| Relative humidity |
5...95% noncondensing
|
| Conducted RF immunity |
10V rms with 1 kHz sine wave 80% AM from 150 kHz...80 MHz on shielded signal ports
|
| Surge transient immunity |
±2 kV line-earth (CM) on shielded signal ports
|
| Operating temperature |
0 °C <60 °C (32 °F <140 °F)
|
| Radiated RF immunity |
10 V/m with 1 kHz sine-wave 80% AM from 80...2000 MHz, 10 V/m with 200 Hz 50% pulse 100% AM @ 900 MHz, 10 V/m with 200 Hz 50% pulse 100% AM @ 1890 MHz, 3 V/m with 1 kHz sine-wave 80% AM from 2000...2700 MHz
|
| Nonoperating temperature |
-40 °C
|
| RTB keying |
User-defined mechanical
|
|---|---|
| Vibration |
2 G @ 10...500 Hz
|
| Shock |
Operating: 30 G, Non operating: 50 G
|
| Slot width |
1
|
| Calibration interval |
12 mo typical
|
|---|---|
| ATEX temperature code |
T4
|
| IECEx temperature code |
T4
|
| Input impedance |
250 Ω ±5 Ω
|
|---|
| Isolation voltage |
250V (continuous), Reinforced insulation type, inputs to backplane, Basic insulation type, input to input, and inputs to ground.
|
|---|
| Enclosure type rating |
None (open-style)
|
|---|
登录您的罗克韦尔自动化帐户以查看和下载技术图纸.
登录
| 基本信息 | 出版 |
|---|---|
| Product Profile | -- |
| Technical Detail | -- |
| Product Cutsheet | -- |
| 技术数据 | 出版 |
|---|---|
| 1756-td002_-en-e | 1756-TD002 |
| 用户手册 | 出版 |
|---|---|
| 1756-um533_-en-p | 1756-UM533 |
提供下载
- DTM Library Software for the 1756-IF8IH Module v1.001
- Firmware for 1756-IF8IH v1.001
- EDS files for 1756-IF8IH (multi)
- EDS files for ControlLogix Family (multi)
- AOP - Add On Profiles for 1756 HART I/O v40.12.23
- China CCC
- MOROCCO DOC
截至 2026-01-15，此产品已获得上述多项认证。此日期前后销售的产品，所获认证可能有所不同。请查阅产品标签，确认具体产品所持有的相关认证。
技术规格
| Display |
Module Health, In Calibration,Mode
|
|---|---|
| Input Signal |
0-20mA, 4-20mA
|
| Isolation |
250V (continuous), reinforced,insulation type, inputs to,backplane
|
| Number Of Channels |
8
|
| Special Features |
Supports HART Protocol
|
| Input, current |
Yes
|
|---|---|
| Input, voltage |
Yes
|
| Input, resistor |
No
|
| Input, resistance thermometer |
No
|
| Input, thermocouple |
No
|
| Input signal, configurable |
Yes
|
| Output, current |
No
|
| Output, voltage |
No
|
| Output signal configurable |
No
|
| Analogue inputs configurable |
Yes
|
| Analogue outputs configurable |
No
|
| Type of electric connection |
Screw-/spring clA connection
|
| Input offset drift with temperature |
<=300 µA/°C
|
| Wire type |
Copper
|
| Terminal block torque specifications |
1756-TBCH: 0.5 Nm (4.4 in-lb)
|
| Inrush current |
400mA @ 5V, 450mA @ 24V
|
| Input conversion method |
Sigma-Delta ADC (24-bit converter)
|
| Module keying |
Electronic, software configurable
|
| Module error over full temperature range |
0.3% of range (all filters) with HART disabled
|
| Input range |
0...20 mA (0...20.58 mA), 4...20 mA (3.42...20.58 mA)
|
| Data format |
32-bit floating point
|
| Wire category |
2 - on signal ports
|
| Common mode noise rejection |
>90 dB @ 50/60 Hz (10 Hz, 15 Hz or 20 Hz filters only)
|
| Normal mode noise rejection |
>90 dB @ 50 Hz and 60 Hz with 10 Hz filter, >74 dB @ 50 Hz and 60 Hz with 15 Hz filter, >33 dB @ 50 Hz and >90 dB @ 60 Hz with 20 Hz filter
|
| Gain drift with temperature |
20 ppm/°C
|
| Voltage and current ratings |
Backplane: 210mA @ 5.1V DC, 110mA @ 24V DC, Input voltage range: 5...30V DC, Input current range: 0...20mA @ 4...20mA
|
| Typical module HART dynamic variables update time for all channels |
1 s typical if all channels are HART enabled Pass through messages, handheld communications, sary masters, communication errors, or configuration changes can significantly increase the update time.
|
| Module scan time |
18...488 ms (filter dependent) for all channels - analog, minimum
|
| Inputs |
Eight current inputs
|
| Resolution |
16 to 21 bit
|
| Wire size |
Single wire connection (1756-TBCH): 0.33...2.1 mm² (22...14 AWG) solid or stranded shielded copper wire, rated at 105 °C (221 °F) or greater, 1.2 mm (3/64 in.) insulation maximum, Single wire connection (1756-TBS6H): 0.33...2.1 mm² (22...14 AWG) solid or
|
| Calibrated accuracy |
0.15...1.5% of full scale, filter dependent@ 25 °C with HART disabled, 1.5% of full scale with 250 Hz filter @ 25 °C with HART enabled, 0.5% of full scale with 100 Hz filter @ 25 °C with HART enabled, 0.2% of full scale with 50 Hz or 60 Hz filter @ 25 °C
|
| Open circuit detection time |
5 s (4...20 mA range only)
|
| Suitable for safety functions |
No
|
| Power dissipation within module |
4 W
|
| Input overvoltage protection |
28.8V DC
|
| Surrounding air temperature, max |
60 °C
|
|---|---|
| North American temperature code |
T5
|
| Emissions |
IEC 61000-6-4
|
| ESD immunity |
6 kV contact discharges, 8 kV air discharges
|
| EFT/B immunity |
±2kV @ 5kHz on signal ports
|
| Relative humidity |
5...95% noncondensing
|
| Conducted RF immunity |
10V rms with 1 kHz sine wave 80% AM from 150 kHz...80 MHz on shielded signal ports
|
| Surge transient immunity |
±2 kV line-earth (CM) on shielded signal ports
|
| Operating temperature |
0 °C <60 °C (32 °F <140 °F)
|
| Radiated RF immunity |
10 V/m with 1 kHz sine-wave 80% AM from 80...2000 MHz, 10 V/m with 200 Hz 50% pulse 100% AM @ 900 MHz, 10 V/m with 200 Hz 50% pulse 100% AM @ 1890 MHz, 3 V/m with 1 kHz sine-wave 80% AM from 2000...2700 MHz
|
| Nonoperating temperature |
-40 °C
|
| RTB keying |
User-defined mechanical
|
|---|---|
| Vibration |
2 G @ 10...500 Hz
|
| Shock |
Operating: 30 G, Non operating: 50 G
|
| Slot width |
1
|
| Calibration interval |
12 mo typical
|
|---|---|
| ATEX temperature code |
T4
|
| IECEx temperature code |
T4
|
| Input impedance |
250 Ω ±5 Ω
|
|---|
| Isolation voltage |
250V (continuous), Reinforced insulation type, inputs to backplane, Basic insulation type, input to input, and inputs to ground.
|
|---|
| Enclosure type rating |
None (open-style)
|
|---|
图纸
登录您的罗克韦尔自动化帐户以查看和下载技术图纸.
登录
文档
|
Product Profile
基本信息
-- |
|
Technical Detail
基本信息
-- |
|
Product Cutsheet
基本信息
-- |
|
1756-td002_-en-e
技术数据
1756-TD002 |
|
1756-um533_-en-p
用户手册
1756-UM533 |
| 基本信息 | 出版 |
|---|---|
| Product Profile | -- |
| Technical Detail | -- |
| Product Cutsheet | -- |
| 技术数据 | 出版 |
| 1756-td002_-en-e | 1756-TD002 |
| 用户手册 | 出版 |
| 1756-um533_-en-p | 1756-UM533 |
下载
提供下载
- DTM Library Software for the 1756-IF8IH Module v1.001
- Firmware for 1756-IF8IH v1.001
- EDS files for 1756-IF8IH (multi)
- EDS files for ControlLogix Family (multi)
- AOP - Add On Profiles for 1756 HART I/O v40.12.23
认证
- China CCC
- MOROCCO DOC
截至 2026-01-15，此产品已获得上述多项认证。此日期前后销售的产品，所获认证可能有所不同。请查阅产品标签，确认具体产品所持有的相关认证。
替代产品
技术说明
Loading
Copyright ©2026 Rockwell Automation, Inc.